TIER: C+ :: DUSTY_ARCHIVEENTROPY_INDEX: 0.91472OBSERVED_COUNT:
Digital Archaeology Report (September 23, 2013): the world was reading about 'Cutting Through the Cloud'. crypto enthusiasts were buying Bitcoin at $133. the number one track on Billboard was 'Roar by Katy Perry'.
CURATION_LOG_ANALYSIS
DATA_ORIGIN2026_ARCHIVE
TRAFFIC_VOL4913
SIGNAL_RES34
NODE_CATPeople & Blogs
SYSTEM ANALYSIS & HEURISTIC REPORT :: NODE [db58baab740c]
Section_1: Asset Profile & Classification
The creator "withcheesepls" released the digital stream "Fade 3 LEDs arduino" in 2013. This asset, with a runtime of 0h 0m 25s, is a contribution to the "People & Blogs" category and is identified by our system as a piece of "General Content".
Section_2: Performance Metrics & Virality Analysis
Quantitative analysis shows 4913 impressions and 34 positive acknowledgments. The asset's Engagement Depth of "1.59" is a key indicator of audience investment. The calculated Virality Score of "0.01" reflects its distribution velocity relative to its age.
| View Count | 4913 |
| Audience Engagement Depth | 1.59 |
| Virality Index | 0.01 |
Section_3: Semantic Content Analysis
The primary content vector is directed towards "General Content". The title acts as the vector's origin and magnitude, pointing users directly to the intended information. This asset is a model of semantic efficiency within the "People & Blogs" field.
Section_4: Contextual Significance & Audience Profile
More than just a broadcast, this asset functions as a conversation catalyst. Its subject matter, presented as "General Content", is designed to elicit responses and foster discussion. The engaged audience profile reflects this, showing a community built around the topics "withcheesepls" explores.
Section_5: System Directive & Final Verdict
COMMUNITY SERVICE VALUE: High. The asset [db58baab740c] functions as a cornerstone for its specific sub-community, providing a valuable and reliable resource. Directive: Mark as a key community asset to ensure its long-term findability for both new and existing members.
ESTABLISHING_CONNECTION...
DATA_NODE: withcheesepls
PUBLISHED2013-09-23
DURATION25s
VIEWS4,913
ENGAGEMENT56 units
//source code. enjoy!
//better code in the comments (this description does not allow brackets, so i can't put it here)
int red = 5; //the first three lines are location of leds
int green = 6;
int blue = 3;
int turn = 0; //turn is whose turn is it to turn on, 0 is red, 1 is blue and 2 is green; this is just to make switching easier
int fade = 5; // amount of fade
int startblue = 0; //this is the birghness of the leds i should have named it brightblue, brightgreen etc.
int startgreen = 0;
int startred = 0;
void setup(){
pinMode(red,OUTPUT); //sets led outputs
pinMode(green,OUTPUT);
pinMode(blue,OUTPUT);
}
void loop(){
startred = startred + fade; //these three lines is the fading, it does not show up until its turn is up.
startblue = startblue + fade;
startgreen = startgreen +fade;
//first is the red leds turn which turn starts w/ 0 it faded up then down
if (turn == 0 ){
analogWrite(red,startred);
if (startred == 255){
fade = -fade; //negate the fade to go down
}
}
//once it reaches all the way done it negates the fade again to prepare the blue to fade and it switches the turn to 1 so blue can start
if (fade == -5 && startred == 0 && turn == 0){
turn = 1;
fade = -fade;
}
//blue's turn, same thing as red, fades up, then down
if (turn== 1){
analogWrite(blue,startblue);
if (startblue ==255){
fade = -fade;
}
}
//switches to green and negatives fade to prepare for green
if (turn == 1 && fade ==-5 && startblue == 0){
turn = 2;
fade =-fade;
}
if (turn == 2){
analogWrite(green,startgreen);
if (startgreen == 255){
fade = -fade;
}
}
// finally it resets to 0 to start w. red again
if (turn == 2 && fade ==-5 && startgreen == 0){
turn = 0;
fade = -fade;
}
delay (50); //delay to make it smooth
}
//better code in the comments (this description does not allow brackets, so i can't put it here)
int red = 5; //the first three lines are location of leds
int green = 6;
int blue = 3;
int turn = 0; //turn is whose turn is it to turn on, 0 is red, 1 is blue and 2 is green; this is just to make switching easier
int fade = 5; // amount of fade
int startblue = 0; //this is the birghness of the leds i should have named it brightblue, brightgreen etc.
int startgreen = 0;
int startred = 0;
void setup(){
pinMode(red,OUTPUT); //sets led outputs
pinMode(green,OUTPUT);
pinMode(blue,OUTPUT);
}
void loop(){
startred = startred + fade; //these three lines is the fading, it does not show up until its turn is up.
startblue = startblue + fade;
startgreen = startgreen +fade;
//first is the red leds turn which turn starts w/ 0 it faded up then down
if (turn == 0 ){
analogWrite(red,startred);
if (startred == 255){
fade = -fade; //negate the fade to go down
}
}
//once it reaches all the way done it negates the fade again to prepare the blue to fade and it switches the turn to 1 so blue can start
if (fade == -5 && startred == 0 && turn == 0){
turn = 1;
fade = -fade;
}
//blue's turn, same thing as red, fades up, then down
if (turn== 1){
analogWrite(blue,startblue);
if (startblue ==255){
fade = -fade;
}
}
//switches to green and negatives fade to prepare for green
if (turn == 1 && fade ==-5 && startblue == 0){
turn = 2;
fade =-fade;
}
if (turn == 2){
analogWrite(green,startgreen);
if (startgreen == 255){
fade = -fade;
}
}
// finally it resets to 0 to start w. red again
if (turn == 2 && fade ==-5 && startgreen == 0){
turn = 0;
fade = -fade;
}
delay (50); //delay to make it smooth
}